A set for MASTER injectors disassembly KB07002

The device for cutting and making ends of brake, hydraulic, copper, copper-nickel and thin-walled steel wires.

Oil Pan Thread Repair Set M14x1,5 na M17x1,5 KB0025-3.

Ściągacz bezwładnościowy wtryskiwaczy piast bębnów

A specialist puller for dismantling Mercedes CDI injectors. The injector puller by screwing in Mercedes CDI engines with hardened bolt and thrust bearing.

A set of cutters for regeneration of injector slots.

Pliers for quick and easy assembly and disassembly of sealants on the motor head. 

The set is used to disassemble and assemble the front axle hub and bearings with the FORD Transit after 2000.

The key for adjusting the 27The key for adjusting the 27-42 mm steering rods.-42 mm steering rods.

Set of 4 hooks with a handle. Hooks have hardened and chrome tips. The handle is made of high-quality non-slip material. Total length of tools - 135 mm.

Universal spring pullers are essential for professional chassis service. 

Socket wrenches for Lambda probe set 2 pcs. Lambda (hot) end cap 1, 2 ", 22 mm x 50 mm, vacuum sensor and lambda probe (for low-seated probes) 3, 8", 22 mm x 30 mm.

Oil Pan Thread Repair Set M14x1,5 na M17x1,5 KB0025-3.

The torque wrench protractor for final tightening of bolts and nuts.

A rich set of hammer hammers and thread adapters for dismantling Common Rail injectors. Everything in a practical case that makes it easier to keep order and prevent losing parts.

The extruder is used to repair a round pipe profile or to expand the pipe diameter in order to connect two pipes with the same diameters. 

A set of pliers for wristbands adapted for Ford, VAG, Mercedes and other systems on the Polish market.

Puller for disassembly of O-rings and simings.

The set consists of 4 levers.

Clutch alingment tool set 17-piece KB04227.

The spanner has a torque range adjustable from 40 to 220 Nm. Equipped with torque lock.

Indispensable tool in every service and workshop, designed to tighten screws with pre-set torque.

The spanner has a torque range adjustable from 42 to 210 Nm. Equipped with a torque lock.

Set for dismantling the missing glow plugs KB02116.

Oil filter pliers 10".

Make sure valves seat perfectly during a top-end rebuild.

The device is designed for precise measurements of the curvature of the front suspension support pipes.

Lever set for upholstery clasps 27 pcs.

Flat band clamp pliers used in cooling circuits.

Professional set of lambda probe caps 7 parts.

Universal spring pullers are essential for professional chassis service. 

Devices for assembly and disassembly of multi-groove belts.

Set for 12 brake pistons, universal for most cars. 

Stand for mounting a 900 kg engine, foldable, workshop helper for working with the engine.

Thread repair set.

Walizka narzędziowa 171 elementów.

Stand for mounting the engine 900 kg, workshop helper for working with the engine.

Professional device that is used to pull ball joints from steering rods in large passenger cars, SUVs and delivery vans.

Specialized attachments are used to assemble and disassemble shock absorbers.

46pcs Socket Tool Set.

Universal kit for disassembly / squeezing bearings and bolt pins 

Professional hole-and-felcarka used for cutting holes and making a felce, or bends along the edge of the sheet allowing you to connect two elements together. 

Universal extractor for extruding the injectors.

The set is used to disassemble and assemble the front axle hub and bearings with the FORD Transit after 2000.

A professional set for repairing various types of threads, including oil sumps, gearboxes, differentials. 

Set for setting camshafts VW; AUDI 1.6, 2.0, 2.7, 3.0, 4.0 4.2 TDI Common Rail and Porsche 3.0 TDi.

A set of cutters for regeneration of injector slots.

The key for adjusting the 27The key for adjusting the 27-42 mm steering rods.-42 mm steering rods.

Pliers for quick and easy assembly and disassembly of sealants on the motor head. 

Tongs for wristbands.

A set of plastic buckles for prying the pins.

A professional stand for mounting engines. The motor is mounted to the stand with 4 metal screws. 

Puller for joints, equipped with all required adapters. It is used to disassemble ball joints. The opening of the arm is 152 mm.

High quality cross key for wheels with 1/2 ", 17, 19, 21mm ends, 250mm long.

DSG Clutch Removal Kit for VW Group C05/0213

A professional set of keys for dismantling radio receivers in cars, indispensable in car services. 

The set is used in the dismantling of valves in OHV and OHC engines without the need to disassemble the head.

13 pieces of sheet metal spoons for car body, long and short in the set.

The key for the timing belt tensioner VW Audi.

A set of tools for valve sealants.

H10 Allen wrench with 7.5 mm hole for unscrewing the BOSCH injector valve.

10 pcs sensor socket set. Remove oxygen sensors, injectors, oil pressure sending units and vacuum switches.

Device for replacing the crankshaft VW.

The set is used for setting and installing bearings and hubs, for sleeve and shaft. 

Hard tools made of glass fiber reinforced plastic. 

Crimping pliers for flexible hoses with 1/2 "to 3/4" jaws.

Professional set of keys for (de) mounting of Bosch and Magneti Mareli alternators.

Set of 4 hooks with a handle. Hooks have hardened and chrome tips. The handle is made of high-quality non-slip material. Total length of tools - 135 mm.

108pcs Socket Tool Set YZ0804001

The subject of the auction is a set of pullers for ball pins, high quality steering rod ends made of forged steel. 

Set of socket wrenches for 14 element filters.

A stroboscope lamp for setting the ignition angle is used to check and adjust the ignition timing of gasoline engines. 

Set of lever for ball joints 3 pcs. Universal has a screwed arm, adapter.

Bit set torx, hex, spline -54 pcs KB04760

Adapter, key for setting the variable camshaft unit VANOS BMW M62 and Range Rover Land Rover 4.4 8V.

A workshop helper for working with the engine. It has four movable grippers fastened to a plate that rotates 360 degrees. 

Universal set for extruding the injectors with a hydraulic cylinder.

Retaining ring pliers.

Handwheel - screwdriver.

The professional vacuum pump produces pressure and vacuum, designed for checking:

- fuel supply system,
- pressure sensors (operating range),
- exhaust gas recirculation valve,
- throttle,
- fuel pressure regulator,
- pressure modulator in automatic transmissions,
- brake assistance.

A set of filters for testing Common Rail injectors. 

Klucz nakrętki łożyska koła osi tył mercedes VARIO C01/0164

High-quality reinforced cross-wrench for wheels, has 4 tips: 17mm, 19mm, 21mm, 23mm. 

The key for adjusting the 27-42mm steering rods.

Pin drawing pliers.

This tool is designed to rivet chain links to form an endless chain and is versatile enough to be used on cam chain todrive chains or as a chain breaker by pushing the pin out.

Wristband pliers set of 2 pcs.

Mounting and dismounting kit for driveshaft with 295 mm bearings.

Sandblasting gun for cabin sandblaster.

Cable ties used in cooling circuits.

The device for cutting and making ends of brake, hydraulic, copper, copper-nickel and thin-walled steel wires.

Zestaw do montażu i demontażu pasków klinowych jest bardzo pomocny podczas ściągania i zakładania pasków na koła pasowe.

Application: dismantling of valves in OHV and OHC engines, without dismantling the head. 

Crimping and cutting pliers.

Thread repair set for repairing various types of thread, including oil pan, gearbox, differential.

Impact screwdriver with a shank and four tips in a practical plastic organizer.

3pc Fuel Line Disconnect Set.

Hand grease 120ml.

The kit for testing the fuel pump carburettor and automatic gearboxes is used for synchronization of car and motorcycle carburettors, 2 and 4 throat. 

The set enables quick and easy assembly or disassembly of the control arm sleeve, without the need to pull the rear or front bars of the rocker arms.

Bit set torx, hex, spline-40 el.

The timing belt tension indicator can be used to adjust the timing belt movement in the range (1daN = 10N). 

Keys for oil plugs 12 parts.

The BMW DIESEL belt pulley wrench.

Set of hooks and scrapers set of 5 pieces.

A specialist puller for dismantling Mercedes CDI injectors. The injector puller by screwing in Mercedes CDI engines with hardened bolt and thrust bearing.

Professional puller for broken bolts and pins. 

A set of sockets and keys for an alternator 24poz.

Pliers for brake springs, features:

• product weight: 1 kg.

Piston ring tools 110-160 mm.

Impact adapters.

The thread set M5 is used to replace a broken thread e.g. in head, engine block housing etc.

Auxiliary sleeve for adjusting the camshaft position.

The device for screwing the brake pistons.

Special kit for assembling and disassembling silent blocks in the front control arm VAG.

Hose clamp pliers for CLIC-R clamps.

Zestaw naprawczy 3/8 do grzechotki CCU-0057

The spanner has a torque range adjustable from 42 to 210 Nm. Equipped with a torque lock.

A set of filters for testing Common Rail injectors. 

The tool is used to press in and out the pins without disassembly the control arm, thus saving you time and energy.

Clutch alingment tool set 17-piece KB04227.

Thread repair set for repairing various types of thread, including oil pan, gearbox, differential.

The thread set M5 is used to replace a broken thread e.g. in head, engine block housing etc.

The torque wrench protractor for final tightening of bolts and nuts.

New, improved by 12 elements set. Required for gasoline and Diesel engines when replacing the timing belt, as well as for the older 1.9D engine (from 76).

General instructions for health and safety Workshops for vulcanization, work in accordance with the PIP and Health and Safety regulations.

Retaining ring pliers.

High quality cross key for wheels with 1/2 ", 17, 19, 21mm ends, 250mm long.

The tool is used to press in and out the pins without disassembly the control arm, thus saving you time and energy.

Clutch alingment tool set 17-piece KB04227.

Thread repair set for repairing various types of thread, including oil pan, gearbox, differential.

The thread set M5 is used to replace a broken thread e.g. in head, engine block housing etc.

The torque wrench protractor for final tightening of bolts and nuts.

The extruder is used to repair a round pipe profile or to expand the pipe diameter in order to connect two pipes with the same diameters. 

Universal spring pullers are essential for professional chassis service. 

Professional set of keys for (de) mounting of Bosch and Magneti Mareli alternators.

Set of socket wrenches for 14 element filters.

Thread repair set.

A set of plastic buckles for prying the pins.