Hard tools made of glass fiber reinforced plastic. Includes 11 levers, upholstery buckets of various shapes and sizes. A set of upholstery tools included in a handy pocket.
Professional hole-and-felcarka used for cutting holes and making a felce, or bends along the edge of the sheet allowing you to connect two elements together.
Flat band clamp pliers used in cooling circuits.
Puller for joints, equipped with all required adapters. It is used to disassemble ball joints. The opening of the arm is 152 mm.
A stroboscope lamp for setting the ignition angle is used to check and adjust the ignition timing of gasoline engines.
A set of sockets and keys for an alternator 24poz.
Clutch alingment tool set 17-piece KB04227.
Pin drawing pliers.
Professional set of keys for (de) mounting of Bosch and Magneti Mareli alternators.
A specialist puller for dismantling Mercedes CDI injectors. The injector puller by screwing in Mercedes CDI engines with hardened bolt and thrust bearing.
Cable ties used in cooling circuits.
Application: dismantling of valves in OHV and OHC engines, without dismantling the head.
Auxiliary sleeve for adjusting the camshaft position.
Piston ring tools 110-160 mm.
The device for cutting and making ends of brake, hydraulic, copper, copper-nickel and thin-walled steel wires.
Tongs for wristbands.
Universal spring pullers are essential for professional chassis service.
H10 Allen wrench with 7.5 mm hole for unscrewing the BOSCH injector valve.
The device for screwing the brake pistons.
Sandblasting gun for cabin sandblaster.
Wristband pliers set of 2 pcs.
Crimping and cutting pliers.
Bit set torx, hex, spline-40 el.
Hard tools made of glass fiber reinforced plastic.
Puller for joints, equipped with all required adapters. It is used to disassemble ball joints. The opening of the arm is 152 mm.
Socket wrenches for Lambda probe set 2 pcs. Lambda (hot) end cap 1, 2 ", 22 mm x 50 mm, vacuum sensor and lambda probe (for low-seated probes) 3, 8", 22 mm x 30 mm.
The set is used to disassemble and assemble the front axle hub and bearings with the FORD Transit after 2000.
Professional puller for broken bolts and pins.
Universal kit for disassembly / squeezing bearings and bolt pins
The thread set M5 is used to replace a broken thread e.g. in head, engine block housing etc.
The spanner has a torque range adjustable from 42 to 210 Nm. Equipped with a torque lock.
Oil filter pliers 10".
Device for assembling and disassembling the wrist joint in the steering system.
Set of hooks and scrapers set of 5 pieces.
The torque wrench protractor for final tightening of bolts and nuts.
Thread repair set for repairing various types of thread, including oil pan, gearbox, differential.
Set for setting camshafts VW; AUDI 1.6, 2.0, 2.7, 3.0, 4.0 4.2 TDI Common Rail and Porsche 3.0 TDi.
Stand for mounting a 900 kg engine, foldable, workshop helper for working with the engine.
3pc Fuel Line Disconnect Set.
Flat band clamp pliers used in cooling circuits.
The BMW DIESEL belt pulley wrench has a diameter of 57mm.
A set of pliers for wristbands adapted for Ford, VAG, Mercedes and other systems on the Polish market.
A set of tools for valve sealants.
Professional device that is used to pull ball joints from steering rods in large passenger cars, SUVs and delivery vans.
Device for replacing the crankshaft VW.
Klucz nakrętki łożyska koła osi tył mercedes VARIO C01/0164
Pliers for quick and easy assembly and disassembly of sealants on the motor head.
Retaining ring pliers.
Set of 4 hooks with a handle. Hooks have hardened and chrome tips. The handle is made of high-quality non-slip material. Total length of tools - 135 mm.
Zestaw do montażu i demontażu pasków klinowych jest bardzo pomocny podczas ściągania i zakładania pasków na koła pasowe.
Universal spring pullers are essential for professional chassis service.
Set for dismantling the missing glow plugs KB02116.
The subject of the auction is a set of pullers for ball pins, high quality steering rod ends made of forged steel.
46pcs Socket Tool Set.
The BMW DIESEL belt pulley wrench.
10 pcs sensor socket set. Remove oxygen sensors, injectors, oil pressure sending units and vacuum switches.
Impact screwdriver with a shank and four tips in a practical plastic organizer.
The timing belt tension indicator can be used to adjust the timing belt movement in the range (1daN = 10N).
Professional hole-and-felcarka used for cutting holes and making a felce, or bends along the edge of the sheet allowing you to connect two elements together.
13 pieces of sheet metal spoons for car body, long and short in the set.
Lever set for upholstery clasps 27 pcs.
A rich set of hammer hammers and thread adapters for dismantling Common Rail injectors. Everything in a practical case that makes it easier to keep order and prevent losing parts.
Handwheel - screwdriver.
Special kit for assembling and disassembling silent blocks in the front control arm VAG.
A professional stand for mounting engines. The motor is mounted to the stand with 4 metal screws.
High-quality reinforced cross-wrench for wheels, has 4 tips: 17mm, 19mm, 21mm, 23mm.
Set of lever for ball joints 3 pcs. Universal has a screwed arm, adapter.
A professional set for repairing various types of threads, including oil sumps, gearboxes, differentials.
Impact adapters.
A professional set of keys for dismantling radio receivers in cars, indispensable in car services.
Walizka narzędziowa 171 elementów.
Pliers for brake springs, features:
Crimping pliers for flexible hoses with 1/2 "to 3/4" jaws.
Kit for regeneration, thread repair.
A set of plastic buckles for prying the pins.
The set enables quick and easy assembly or disassembly of the control arm sleeve, without the need to pull the rear or front bars of the rocker arms.
Set of socket wrenches for 14 element filters.
The set consists of 4 levers.
The kit for testing the fuel pump carburettor and automatic gearboxes is used for synchronization of car and motorcycle carburettors, 2 and 4 throat.
The key for adjusting the 27The key for adjusting the 27-42 mm steering rods.-42 mm steering rods.
Keys for oil plugs 12 parts.
Mounting and dismounting kit for driveshaft with 295 mm bearings.
Universal set for extruding the injectors with a hydraulic cylinder.
The device is designed for precise measurements of the curvature of the front suspension support pipes.
Make sure valves seat perfectly during a top-end rebuild.
The key for the timing belt tensioner VW Audi.
A workshop helper for working with the engine. It has four movable grippers fastened to a plate that rotates 360 degrees.
The key for adjusting the 27-42mm steering rods.
DSG Clutch Removal Kit for VW Group C05/0213
Hand grease 120ml.
The professional vacuum pump produces pressure and vacuum, designed for checking:
- fuel supply system,
- pressure sensors (operating range),
- exhaust gas recirculation valve,
- throttle,
- fuel pressure regulator,
- pressure modulator in automatic transmissions,
- brake assistance.
High quality cross key for wheels with 1/2 ", 17, 19, 21mm ends, 250mm long.
Thread repair set.
A set of cutters for regeneration of injector slots.
Adapter, key for setting the variable camshaft unit VANOS BMW M62 and Range Rover Land Rover 4.4 8V.
Set for springs and brake cups.
Self-locking pliers for cutting exhaust pipes.
A stroboscope lamp for setting the ignition angle is used to check and adjust the ignition timing of gasoline engines.
108pcs Socket Tool Set YZ0804001
The set is used for setting and installing bearings and hubs, for sleeve and shaft.
Devices for assembly and disassembly of multi-groove belts.
Hose clamp pliers for CLIC-R clamps.
The spanner has a torque range adjustable from 40 to 220 Nm. Equipped with torque lock.
Indispensable tool in every service and workshop, designed to tighten screws with pre-set torque.
This tool is designed to rivet chain links to form an endless chain and is versatile enough to be used on cam chain todrive chains or as a chain breaker by pushing the pin out.
Set for 12 brake pistons, universal for most cars.
A set of filters for testing Common Rail injectors.
Professional set of lambda probe caps 7 parts.
Universal extractor for extruding the injectors.
The set is used in the dismantling of valves in OHV and OHC engines without the need to disassemble the head.
Puller for disassembly of O-rings and simings.
New, improved by 12 elements set. Required for gasoline and Diesel engines when replacing the timing belt, as well as for the older 1.9D engine (from 76).
Quick coupling - external copper thread.
The key for adjusting the 27The key for adjusting the 27-42 mm steering rods.-42 mm steering rods.
The tool is used to press in and out the pins without disassembly the control arm, thus saving you time and energy.
Clutch alingment tool set 17-piece KB04227.
Thread repair set for repairing various types of thread, including oil pan, gearbox, differential.
The thread set M5 is used to replace a broken thread e.g. in head, engine block housing etc.
The torque wrench protractor for final tightening of bolts and nuts.
Adapter for extracting TDI PD-PD pump / injectors.
Quick coupling - external copper thread.
Retaining ring pliers.
The tool is used to press in and out the pins without disassembly the control arm, thus saving you time and energy.
Clutch alingment tool set 17-piece KB04227.
Thread repair set for repairing various types of thread, including oil pan, gearbox, differential.
The thread set M5 is used to replace a broken thread e.g. in head, engine block housing etc.
The torque wrench protractor for final tightening of bolts and nuts.
3pc Fuel Line Disconnect Set.
Set for springs and brake cups.
Hose clamp pliers for CLIC-R clamps.
Opening days:
Mondays to Fridays
8:00am - 5:00pm
Headquarters
CASTEX Anna Bednarz
ul. Ludwikowo 2C
85-502 Bydgoszcz, Poland
Call Us
+48 52 515 64 22
+48 500 616 500
Write Us
biuro@castex.pl
office@castex.pl
Szanowna Klientko, Szanowny Kliencie na naszych stronach używamy technologii, takich jak pliki cookie, do zbierania i przetwarzania danych osobowych w celu personalizowania treści i reklam oraz analizowania ruchu na stronach i w Internecie. Pragniemy zapoznać Cię ze szczegółami stosowanych przez nas technologii oraz z przepisami, które od 25.05 2018 r. weszły do użycia na terenie całej UE, tak aby dać Ci pełną wiedzę i komfort w korzystaniu z naszych usług internetowych. Zapoznaj się z poniższymi informacjami przed przejściem do sklepu. Klikając przycisk „Akceptuję” lub zamykając to okno zgadzasz się na postanowienia zawarte w naszej polityce prywatności i polityce plików cookies.
Akceptuj Więcej informacji Odrzuć