Wire Thread Inserts - M8 X 1.25 - 25 PCS - KBJ1054

Adapter, key for setting the variable camshaft unit VANOS BMW M62 and Range Rover Land Rover 4.4 8V.

Stand for mounting the engine 900 kg, workshop helper for working with the engine.

The spanner has a torque range adjustable from 42 to 210 Nm. Equipped with a torque lock.

Lever set for upholstery clasps 27 pcs.

Professional puller for broken bolts and pins. 

10 pcs sensor socket set. Remove oxygen sensors, injectors, oil pressure sending units and vacuum switches.

Piston ring tools 110-160 mm.

The set is used to disassemble and assemble the front axle hub and bearings with the FORD Transit after 2000.

The set is used for setting and installing bearings and hubs, for sleeve and shaft. 

Set for springs and brake cups.

Oil filter pliers 10".

A set of cutters for regeneration of injector slots.

Puller for joints, equipped with all required adapters. It is used to disassemble ball joints. The opening of the arm is 152 mm.

Hard tools made of glass fiber reinforced plastic. 

A rich set of hammer hammers and thread adapters for dismantling Common Rail injectors. Everything in a practical case that makes it easier to keep order and prevent losing parts.

Impact adapters.

Adapter, key for setting the variable camshaft unit VANOS BMW M62 and Range Rover Land Rover 4.4 8V.

Impact screwdriver with a shank and four tips in a practical plastic organizer.

A workshop helper for working with the engine. It has four movable grippers fastened to a plate that rotates 360 degrees. 

Auxiliary sleeve for adjusting the camshaft position.

Walizka narzędziowa 171 elementów.

This tool is designed to rivet chain links to form an endless chain and is versatile enough to be used on cam chain todrive chains or as a chain breaker by pushing the pin out.

The key for the timing belt tensioner VW Audi.

Universal extractor for extruding the injectors.

Hose clamp pliers for CLIC-R clamps.

The device is designed for precise measurements of the curvature of the front suspension support pipes.

Socket wrenches for Lambda probe set 2 pcs. Lambda (hot) end cap 1, 2 ", 22 mm x 50 mm, vacuum sensor and lambda probe (for low-seated probes) 3, 8", 22 mm x 30 mm.

The set is used in the dismantling of valves in OHV and OHC engines without the need to disassemble the head.

Oil Pan Thread Repair Set M14x1,5 na M17x1,5 KB0025-3.

The professional vacuum pump produces pressure and vacuum, designed for checking:

- fuel supply system,
- pressure sensors (operating range),
- exhaust gas recirculation valve,
- throttle,
- fuel pressure regulator,
- pressure modulator in automatic transmissions,
- brake assistance.

The set enables quick and easy assembly or disassembly of the control arm sleeve, without the need to pull the rear or front bars of the rocker arms.

High quality cross key for wheels with 1/2 ", 17, 19, 21mm ends, 250mm long.

Handwheel - screwdriver.

The spanner has a torque range adjustable from 42 to 210 Nm. Equipped with a torque lock.

Universal spring pullers are essential for professional chassis service. 

Universal set for extruding the injectors with a hydraulic cylinder.

A set of tools for valve sealants.

Sandblasting gun for cabin sandblaster.

The extruder is used to repair a round pipe profile or to expand the pipe diameter in order to connect two pipes with the same diameters. 

A professional stand for mounting engines. The motor is mounted to the stand with 4 metal screws. 

Device for assembling and disassembling the wrist joint in the steering system.

A specialist puller for dismantling Mercedes CDI injectors. The injector puller by screwing in Mercedes CDI engines with hardened bolt and thrust bearing.

H10 Allen wrench with 7.5 mm hole for unscrewing the BOSCH injector valve.

A set of filters for testing Common Rail injectors. 

Lever set for upholstery clasps 27 pcs.

Set of hooks and scrapers set of 5 pieces.

Cable ties used in cooling circuits.

The device for cutting and making ends of brake, hydraulic, copper, copper-nickel and thin-walled steel wires.

DSG Clutch Removal Kit for VW Group C05/0213

Tongs for wristbands.

Professional puller for broken bolts and pins. 

The key for adjusting the 27The key for adjusting the 27-42 mm steering rods.-42 mm steering rods.

Crimping and cutting pliers.

The device for screwing the brake pistons.

Kit for regeneration, thread repair.

Professional set of keys for (de) mounting of Bosch and Magneti Mareli alternators.

Zestaw do montażu i demontażu pasków klinowych jest bardzo pomocny podczas ściągania i zakładania pasków na koła pasowe.

Hand grease 120ml.

The timing belt tension indicator can be used to adjust the timing belt movement in the range (1daN = 10N). 

Crimping pliers for flexible hoses with 1/2 "to 3/4" jaws.

Thread repair set for repairing various types of thread, including oil pan, gearbox, differential.

Professional hole-and-felcarka used for cutting holes and making a felce, or bends along the edge of the sheet allowing you to connect two elements together. 

Flat band clamp pliers used in cooling circuits.

Wristband pliers set of 2 pcs.

The kit for testing the fuel pump carburettor and automatic gearboxes is used for synchronization of car and motorcycle carburettors, 2 and 4 throat. 

Set of socket wrenches for 14 element filters.

A set of plastic buckles for prying the pins.

13 pieces of sheet metal spoons for car body, long and short in the set.

Set for setting camshafts VW; AUDI 1.6, 2.0, 2.7, 3.0, 4.0 4.2 TDI Common Rail and Porsche 3.0 TDi.

Retaining ring pliers.

3pc Fuel Line Disconnect Set.

The BMW DIESEL belt pulley wrench.

Set for 12 brake pistons, universal for most cars. 

Bit set torx, hex, spline -54 pcs KB04760

Clutch alingment tool set 17-piece KB04227.

The subject of the auction is a set of pullers for ball pins, high quality steering rod ends made of forged steel. 

Set of 4 hooks with a handle. Hooks have hardened and chrome tips. The handle is made of high-quality non-slip material. Total length of tools - 135 mm.

The thread set M5 is used to replace a broken thread e.g. in head, engine block housing etc.

Thread repair set.

Pin drawing pliers.

The key for adjusting the 27-42mm steering rods.

Make sure valves seat perfectly during a top-end rebuild.

Stand for mounting the engine 900 kg, workshop helper for working with the engine.

Universal spring pullers are essential for professional chassis service. 

Puller for disassembly of O-rings and simings.

A set of pliers for wristbands adapted for Ford, VAG, Mercedes and other systems on the Polish market.

Set for dismantling the missing glow plugs KB02116.

The set consists of 4 levers.

Application: dismantling of valves in OHV and OHC engines, without dismantling the head. 

The torque wrench protractor for final tightening of bolts and nuts.

Self-locking pliers for cutting exhaust pipes.

46pcs Socket Tool Set.

Keys for oil plugs 12 parts.

Pliers for quick and easy assembly and disassembly of sealants on the motor head. 

The spanner has a torque range adjustable from 40 to 220 Nm. Equipped with torque lock.

Indispensable tool in every service and workshop, designed to tighten screws with pre-set torque.

Professional device that is used to pull ball joints from steering rods in large passenger cars, SUVs and delivery vans.

Stand for mounting a 900 kg engine, foldable, workshop helper for working with the engine.

Mounting and dismounting kit for driveshaft with 295 mm bearings.

Pliers for brake springs, features:

• product weight: 1 kg.

A stroboscope lamp for setting the ignition angle is used to check and adjust the ignition timing of gasoline engines. 

Devices for assembly and disassembly of multi-groove belts.

Device for replacing the crankshaft VW.

A set of sockets and keys for an alternator 24poz.

High-quality reinforced cross-wrench for wheels, has 4 tips: 17mm, 19mm, 21mm, 23mm. 

Klucz nakrętki łożyska koła osi tył mercedes VARIO C01/0164

Bit set torx, hex, spline-40 el.

Universal kit for disassembly / squeezing bearings and bolt pins 

Specialized attachments are used to assemble and disassemble shock absorbers.

A professional set of keys for dismantling radio receivers in cars, indispensable in car services. 

A professional set for repairing various types of threads, including oil sumps, gearboxes, differentials. 

The device contains a safety valve, it is fixed in the radiator or equalizer cap. Suitable for all traditional liquid cooled engines.

Press, puller for pins, sleeves without adapters C02/0135.

Klucz nakrętki łożyska koła osi tył mercedes VARIO C01/0164

Manual set for cutting windows, which includes:

• threading bar - 1 item
• wire holder - 2 pcs
• spool of square wire - 1 item
• hand knife - 1 item
• clip holder - 2 pcs

The tool is used to press in and out the pins without disassembly the control arm, thus saving you time and energy.

Clutch alingment tool set 17-piece KB04227.

Thread repair set for repairing various types of thread, including oil pan, gearbox, differential.

The thread set M5 is used to replace a broken thread e.g. in head, engine block housing etc.

The torque wrench protractor for final tightening of bolts and nuts.

Handwheel - screwdriver.

A set of cutters for regeneration of injector slots.

Discs for mounting bearings, aluminum - 17 elements KB09022

Universal two- and three-arm puller.

The tool is used to press in and out the pins without disassembly the control arm, thus saving you time and energy.

Clutch alingment tool set 17-piece KB04227.

Thread repair set for repairing various types of thread, including oil pan, gearbox, differential.

The thread set M5 is used to replace a broken thread e.g. in head, engine block housing etc.

The torque wrench protractor for final tightening of bolts and nuts.